Alignment Tools & Adjustment Kits

Hofmann EAA0446J76C : AC200 Wall Mount Storage

Hofmann EAA0446J76C : AC200 Wall Mount Storage

Hofmann EAK0350J80A : AC200 Kit (4 Clamps & 4XD targets) 670XD, 678, 680XD, 770 only

Hofmann EAK0350J80A : AC200 Kit (4 Clamps & 4XD targets) 670XD, 678, 680XD, 770 only

Hofmann EAK0363J88A : Mobility Kit for 609

Hofmann EAK0363J88A : Mobility Kit for 609

Hofmann EAK0363J89A : Clamp Stand for 609

Hofmann EAK0363J89A : Clamp Stand for 609

Hofmann RB24 : Alignment Stands with Bridge Set

Hofmann RB24 : Alignment Stands with Bridge Set

QSP RR-2030 : 20" x 30" Convex mirror with bracket

SPC 23236: 1-1/2° FORD SLEEVE

SPC 23236: 1-1/2° FORD SLEEVE   SKU: 23236   This truck sleeve will correct caster and camber ±1.50° on trucks equipped with the Dana Super 60 solid axle, such as the F450, F550 and GM Topkick. Other sleeve sizes are also available, see below...

SPC 23780: LARGE BJOINT INSTALLATION SET

These sleeves make installation of Offset Ball Joints easy for the installer. The sleeves are designed to match the angle of the yoke on the axle housing to insure proper installation. Sleeve set #23780 is for our Dodge Truck Offset Ball Joints (part nos...

SPC 27: PITMAN ARM SEPARATOR

For use on most cars and some light trucks. The tapered wedge easily removes the pitman arm from the shaft with just a few sharp hammer blows.   DIMENSIONS: 1" opening, 12" overall length.

SPC 41110: BALL JOINT ADAPTOR SET

Expand the service capability of your ball joint press with this Master Ball Joint Adapter Set. This complete kit includes the adapters and receiving tubes needed to work on GM, Ford and Dodge two and four wheel drive trucks, vans and SUVs. Kit also...

SPC 4169: BUSHING SLEEVE SOCKET

Thin walled spanner wrench designed specifically for installation and removal of O.E. and #23000 screw in 4WD alignment sleeves.   CAUTION: Not for use with impact wrenches (air tools).

SPC 45945: GM HD TRUCK TOOL

This wrench makes it easy to adjust the control arm cams on many modern GM and Chevy HD Trucks along with the new Colorado and Canyon. The tool surrounds the entire perimeter of each cam to provide a solid no slip means to reach the hard-to-reach and...

SPC 64225: MAGNETIC ANGLE GAUGE

This angle gauge is an easy, accurate way for measuring frame and drive shaft angles. An ideal tool to ensure the drive line angle is still within specification for raised and lowered vehicles. Alignment equipment manufacturers are using frame angle...

SPC 71909: TIE ROD TOOL SET-5PC

Previously 7190 Tie Rod Tool Kit. This kit includes part numbers 71959 through 71999. It will allow adjustment of most cars and light trucks and also includes the 2 larger adjusting tools needed for the new Ford Super Duty pickups. Tools have a 1/2"...

SPC 74915: CENTER PUNCH STUD (74910)

Center Punch Stud for SPC 74910 Cam Knockout Punch.

SPC 77928: BRAKE PEDAL DEPRESSOR

An adjustable steel plate extends the length of the bar to put constant pressure on the brake pedal.

SPC 79230: FLIP SOCKET 3/4" & 13/16"

These 1/2" square drive impact sockets are deep and thin walled to reach areas conventional sockets can't. Provides two sizes: 3/4" and 13/16"

SPC 81134: REPLACEMENT VIAL FOR 81139

Replacement Vial for SPC 81139 Magnetic Adj Camber Gauge

SPC 82400: DODGE CAMBER/CASTER

SPC 82400: Dodge Camber/Caster   Replace OE cams on the lower control arm of popular Dodge Dakota light trucks with this kit. Get the ±2.0° camber/caster change that you need and lock it in with this simple R and R piece.   Front Adjustment Range:...

SPC 87400: GM TRUCK CAM KIT (4)

SPC 87400: GM Truck Cam Kit (4)   SKU: SPC87400   These heavy duty cams replace the upper control arm mounting bolts. Remove the O.E. bolts and replace with cams, rotating to provide camber and/or caster adjustment. It may be necessary to remove O.E...